S
speedemon
fkin nice man, the mxssh has nice internode spacing, looks tight. gonna be a colafest in there very soon. k+
Thanks Scrogerman Hope your well.
fkin nice man, the mxssh has nice internode spacing, looks tight. gonna be a colafest in there very soon. k+
I have included some up skirt shots for those of you who appreciate them The last pic is Lonestars Killer Queen which derserves a picture on her own due to being an outstanding plant.
Nice idea mate with the piping and clips al be double netting this run too for the top heavy girls
Its a jungle in there mate
Peace
Nice man, that is something I am having to do this week and dreading every minute of it.
Not using dr150 tents again, too deep to do any work without removing plants. Unless I go for an inspector gadget arm upgrade.
I was going to go with pea netting painstakingly pulled down over the colas. Not as a scrog but for support.
I love your scrog nets, wicked setup. Tight, litterally.
Ha ha lol 1.1k scrog gunna be epic mate
peace
Nice one on the upgrade, thinking about a couple of those myself... What type of fan is that you have to the right of the ballast? Looks like it's designed to be quieter than normal RVK style fan.
Needing another 2 screens can only be a good thing, aye
I have no such leaking problems with any of my tds lines. I am sure I would have noticed by now. Lol
Perhaps those buckle things need tightening on yours?
Remember at least 2x2inch squares. You can use chicken wire as well or even some tightly strug rope but I would suggest wire. You need something strong to support the buds and hold back the canopy growth. The screen needs to be cut to size. The size of the screen is determined by the size of your lamp. Remember that to get the good bud formation you want from 50 watts per square foot so your screen size should not exceed that. Check the examples below.
150hps screen size 1.75ft x 1.75ft
250hps screen size 2.25ft x 2.25ft
400hps screen size 2.91ft x 2.75ft
600hps screen size 3.45ft x 3.45ft
1000hps screen size 4.4ft x 4.5ft
Nice grow Speedemon. Just want to ask you or anyone else if you could point me to a good SCROG walkthrough. I'm only growing one plant of NL on my first grow as a test run and want to make sure I have everything down packed. I get the part of building the screen. For me it's how exactly to tuck the plant back under the screen and when to let it above the screen. Am I just topping the plant until I get more apical bud sites and THEY'RE what I'm letting poke through the screen holes? I'm confused on that part. Seeing as how the apical bud sites are what will sprout the actual buds.
EDIT: Ok I just saw you post a walkthrough a few pages back so I won't ask for that. I do need details about the tucking part of it though. Then there's this...
Ok...I'll be using a 200W 3W LED for one plant. These measurements are factoring in HPS not LED...does that change anything? Can't I just apply the range of my LED to the size of the screen? For instance...the LED I'm getting has a total coverage of 3x3.5 ft. Which is perfect for my closet where I'm working with a 3x8 space. So I'm thinking that's how big my screen should be right?
Welcome to IC KillerJah Thanks for the compliment
To tuck the plant under the sceen just reach under the canopyt and gently pull the offending stretcher down through the mesh, and place in another location, or sometimes I train above the mesh by weaving the branch down and up, this works very well
As for went to let go my rule of thumb is after 2nd week of flowering on the smaller cola's and the larger ones then just keep training until stretch stops, an easy method is to pull the cola down from underneath and tie it down.
As for the LED lighting I do not know much about it so you will just have to position where you see best results
Your mesh size sounds right at the same size as your closet 3' x 3.5' which is also the spread of the LED Are you using Mylar on the walls?
I am sure you will master it soon enough, good luck