Hey folks.
I turned this PC into a growbox and all the wiring is pretty much done. My only concern is the fact that moisture, heat, blowing fans and electricity don't always mix well together and this is also my first grow operation. I won't leave the grow unattended for long periods of time but it would royally suck if it was to burn down while i was at the supermarket getting some munchies or something. Here are the basics of the setup and i'll post some pictures of the wiring etc. below. Let me know what you think. Any input is appreciated.
Fan 1:
Noctua NF-F12 industrialPPC-3000 PWM (+ DIY carbon filter)
Max. Input Power 3,6 W
Max. Input Current 0,3 A
Voltage 12 V
Fan 2:
Silverstone FM121
Rated Voltage 12 VDC
Rated Current 0.40A, 0.5A (Max.)
Rated Power 4.8W (Max. 6.0W)
Fan 3:
Silverstone FM121
Rated Voltage 12 VDC
Rated Current 0.40A, 0.5A (Max.)
Rated Power 4.8W (Max. 6.0W)
Fan controller:
Scythe Kaze Q 3.5" Fan Controller
Voltage Range: 5 V (±10%) - 12 V (±10%)
Fan Channels: 4 (max. 1 Ampere / max. 12 W)
All fans get power from the controller, the controller is connected to a 12V DC charger (2,25 A, 27 W), the charger is connected to a extension cord which is equipped with surge protection.
90W COB LED lightning will be added later and that will be connected to a timer, which has a place in the extension cord.
Case is a Nexus edge covered in mylar. Grow medium will be soil.
Silverstone fan wirings are in this wet room junction box. These fans actually had their own independent controllers but i thought it would be neat to connect all three fans to the same control panel.
This is the scythe fan controller and it can be covered with that white styrofoam piece. Is that enough cover though? From moisture?
Also. This is my first post on icmag. Powerful.
I turned this PC into a growbox and all the wiring is pretty much done. My only concern is the fact that moisture, heat, blowing fans and electricity don't always mix well together and this is also my first grow operation. I won't leave the grow unattended for long periods of time but it would royally suck if it was to burn down while i was at the supermarket getting some munchies or something. Here are the basics of the setup and i'll post some pictures of the wiring etc. below. Let me know what you think. Any input is appreciated.
Fan 1:
Noctua NF-F12 industrialPPC-3000 PWM (+ DIY carbon filter)
Max. Input Power 3,6 W
Max. Input Current 0,3 A
Voltage 12 V
Fan 2:
Silverstone FM121
Rated Voltage 12 VDC
Rated Current 0.40A, 0.5A (Max.)
Rated Power 4.8W (Max. 6.0W)
Fan 3:
Silverstone FM121
Rated Voltage 12 VDC
Rated Current 0.40A, 0.5A (Max.)
Rated Power 4.8W (Max. 6.0W)
Fan controller:
Scythe Kaze Q 3.5" Fan Controller
Voltage Range: 5 V (±10%) - 12 V (±10%)
Fan Channels: 4 (max. 1 Ampere / max. 12 W)
All fans get power from the controller, the controller is connected to a 12V DC charger (2,25 A, 27 W), the charger is connected to a extension cord which is equipped with surge protection.
90W COB LED lightning will be added later and that will be connected to a timer, which has a place in the extension cord.
Case is a Nexus edge covered in mylar. Grow medium will be soil.
Silverstone fan wirings are in this wet room junction box. These fans actually had their own independent controllers but i thought it would be neat to connect all three fans to the same control panel.
This is the scythe fan controller and it can be covered with that white styrofoam piece. Is that enough cover though? From moisture?
Also. This is my first post on icmag. Powerful.