bobblehead overtakes

[high life 45]

Diggin the new setup!

 

[Hundred Gram Oz]

Haha hey bobble you forgot to get back to me, I was just wondering about the manifold?

Hey when can we get you over to Ireland to build some shit? I'll pay for your plane ticket .

HGO

 

[DHF]

My boy constantly evolves and overcomes adversity.......Sorry I ever pressed blumats , but many many folks are dialed and hoonin with em and I thought they`d help up your game Bro.......and......

Yeah.....that silicone will never last over those barbs , so getchas some tophat grommets and not worry bout all yer juice endin up on the floor.....

Expansion and contraction from heating and cooling will ultimately break the seal between the silicone and pvc so I`ll leave it to you to upgrade when possible.....

Likin the new lil setup.....Make it happen.....and congrats on the new lil gf stress relief.....good pussy and ass is some wonderful shit.....makes wakin up a whole lot better.......

Peace.....Freds..............

 

[bobblehead]

Haha hey bobble you forgot to get back to me, I was just wondering about the manifold?

Hey when can we get you over to Ireland to build some shit? I'll pay for your plane ticket .

HGO

My bad yo... Yes, the nute solution goes to the room via 1/2" pvc, and enters the 3/4" manifold at a T. That's supposed to help even out pressure, probably why you're asking? I'm thinking about adding a valve at that point to control pressure, should I need to dial down the amount of nute solution being delivered, so that I can increase the frequency...

I suppose I'll share pics when I make that modification.

 

[FlowerFarmer]

Bobster,

Thinking this is sort of what you're looking for. I've seen these at my local shop once, but they've since ran out and never got anymore in.

Just like the 1/4" barbs, but threaded on one end. Just drill a hole slightly smaller and crank em' in.

(cant vouch for the site..just where I found something similar to what I'm talking about).
http://www.dripirrigation.com/drip_irrigation_parts/764

 

[gurnt]

I found this works good for 1/4" lines. A manifold FOR IN DOORS no algae you can get the grommet for $0.08 on e-bay there for tattoo guns

 

[bobblehead]

My boy constantly evolves and overcomes adversity.......Sorry I ever pressed blumats , but many many folks are dialed and hoonin with em and I thought they`d help up your game Bro.......and......

Yeah.....that silicone will never last over those barbs , so getchas some tophat grommets and not worry bout all yer juice endin up on the floor.....

Expansion and contraction from heating and cooling will ultimately break the seal between the silicone and pvc so I`ll leave it to you to upgrade when possible.....

Likin the new lil setup.....Make it happen.....and congrats on the new lil gf stress relief.....good pussy and ass is some wonderful shit.....makes wakin up a whole lot better.......

Peace.....Freds..............

All is forgiven dude, I'm over it... You're my boy. It's not like you did it to sabotage me. I'm damn near achieving financial freedom in large part due to your advice. I'm running multiple flip rooms instead of one large room... Which is probably a large part of why I was able to eliminate the russet/broad mites and root aphids... If they had spread to the whole house because I was running one large perpetual grow, it would have been much more difficult to control, losses could have been worse. It's the little things don't ya know. I'll get this gravity fed DTW dialed to a "T" and you'll be telling everyone about it. Those PPK guys are on notice, they need to watch out.

and yeah... I'm smiling more lately.

Bobster,

Thinking this is sort of what you're looking for. I've seen these at my local shop once, but they've since ran out and never got anymore in.

Just like the 1/4" barbs, but threaded on one end. Just drill a hole slightly smaller and crank em' in.

(cant vouch for the site..just where I found something similar to what I'm talking about).
http://www.dripirrigation.com/drip_irrigation_parts/764

View Image

Word... I would just cover the threads in cement and twist in... I'll check into buying a few to test out before I buy a few hundred...

I found this works good for 1/4" lines. A manifold FOR IN DOORS no algae you can get the grommet for $0.08 on e-bay there for tattoo guns
View Image

Thanks for the tip gurnt!

 

[Hundred Gram Oz]

My bad yo... Yes, the nute solution goes to the room via 1/2" pvc, and enters the 3/4" manifold at a T. That's supposed to help even out pressure, probably why you're asking? I'm thinking about adding a valve at that point to control pressure, should I need to dial down the amount of nute solution being delivered, so that I can increase the frequency...

I suppose I'll share pics when I make that modification.

Yeah Bobbz that's why I was asking. I used to run sort of the same design but I was using 16mm flexi pipe, it's much better having the water intake going both directions once it enters the manifold like your already doing.

When are ya gonna fire her up?

HGO

 

[bobblehead]

It's fired up and running as we type... Hopefully it's working just fine. I've built enough flawed systems, I deserve to have one running right out of the gate, dontcha think? As long as this works out, I'll be replumbing the octagon.... And then Mr. D and FHC are in trouble...

 

[Hundred Gram Oz]

I think ya got this one handled man. How often are ya gonna feed?

A DTW octagon is gonna be a hell of a setup guaranteed, been waiting for someone to do this for a while now.

HGO

 

[Mister_D]

And then Mr. D and FHC are in trouble...

I'm lookng forward to the challenge buddy . Show us how it's done.

 

[Hundred Gram Oz]

And then Mr. D and FHC are in trouble...

That sounds like fighting talk to me

 

[GMax]

It's fired up and running as we type... Hopefully it's working just fine. I've built enough flawed systems, I deserve to have one running right out of the gate, dontcha think? As long as this works out, I'll be replumbing the octagon.... And then Mr. D and FHC are in trouble...

i am coming for that crown too... dont underestimate the sleeper

 

[Mister_D]

GMax the sleeper . You want in on the bet too? First to get 10 pounds from three 600's or two 1000's wins, 10 lbs and bragging rights .

 

[silver hawaiian]

I'll be on hand to help with the winnings. And I ain't really into braggin'.

 

[megayields]

HempCat says Awesome job bro....finally home again!

 

[GMax]

GMax the sleeper . You want in on the bet too? First to get 10 pounds from three 600's or two 1000's wins, 10 lbs and bragging rights .

babyshit...if you trying to lose that money

 

[Mister_D]

babyshit...if you trying to lose that money

Alot of big talk, better start backing it up if you want the crown . Bobble just needs to get his room in order and he's all over it. Me, I'm just sorting out some new elites, then it's game over fellas

 

[GMax]

Alot of big talk, better start backing it up if you want the crown . Bobble just needs to get his room in order and he's all over it. Me, I'm just sorting out some new elites, then it's game over fellas

all in good fun 10 lbs is a big feat, but it possible.. i dont care who does it, i just wanna see it happen

me i need to start growing them heavy yeilders again... i just cant give up the 7 wk flowering SB...in the short run i get little less per harvest, but in the long run i get more harvests per year so it works out well

but back it up i will.. i am 8 weeks out from what i am hoping to be a great harvest

 

[darkstar270]

This thread just keeps getting better, and better!!