looking good mate - if the NL plants dont look identical then you should take a clone of the one you flower just in case it is better than the one you keep for the mum
if you can, always clone every plant you flower - cos its always gonna be the one you didnt back up that ends up being the one you wish you kept
look forward to seeing the new setup
V.
TAMPA , FL , US 07/20/2009 5:54 A.M. OUT FOR DELIVERY
I not sure what height to put the lamp at?
The CoolTube is 24" above the tallest plant with temps of 79-81 degrees F. Relative Humidity is 50-60%
May have to replace the in line and/or exhaust fans and/or install a large circulation fan
I remember in my search seeing a chart that had average coverage/height area for wattages for both HPS and MH .
Anyone have a link to this chart? Anyone?
hey soc glad to see you got your tent and light..as far as the forgotten lamp, well that the breaks , shipping the correct order seems to be difficult for most big places..
now lets address the way you have your tent set up.
I am by no means an expert but .here are my thoughts
1 it seems you are pulling through the scrubber , to the fan then pushing through the cooltube out to the exhaust, while IMO it would better this way,
scrubber----> cool tube ----->fan---> exhaust-->
and ....you want to avoid those bends in the flex duct, you wouldn't believe how much on single 90deg bend will influence the pull or Push through ducting, if ya can make those ducting runs as short as possible and as straight as possible,
PLEASE DONT JUDGE MY DRAWINGS , I JUST HAVE THE ENERGY TO MAKE IT PRETTY,,
you can compress the ducting together to make the runs shorter ( without having to cut the ducting into smaller pieces), , basically you want to have duct runs as short as possible and bends as small as possible
(deg wise)
does this make any sense//kinda tired right now
View attachment 18066
View attachment 18067
air circulation , yea I would suggest another fan in there , those clip fans are great but dont move a lot of air.
obviously the closer ya get the light to the plants the better, with a 600 in that tent 24 inches is fine, 18 inches is better, think about tying the taller plant down, plants seem to be most flexible right before lights on,
I would suggest super cropping but I'm not sure you would be comfortable with it..
I'm in flower and lights are off right now so I cant take any pics of my junk right now ,,
Yes makes perfect sense. Will make it so!you can compress the ducting together to make the runs shorter ( without having to cut the ducting into smaller pieces), , basically you want to have duct runs as short as possible and bends as small as possible
(deg wise)
does this make any sense//kinda tired right now
Yes ,when to Home Depot purchased a stand up fan.air circulation , yea I would suggest another fan in there , those clip fans are great but dont move a lot of air.
I built a screen for the LowRyder (Long Legs) will display next update. Super cropping perhaps with the Northern Lights do not know if LowRyders will take to itI would suggest super cropping but I'm not sure you would be comfortable with it.
duh Yea I forgot about you ac unit
I worry more about the light getting IN the tent during lights off than the light escaping,,you have 600 watts of intense HID light in there, how intense in the light in the place where the tent is setup, since you said you have a door thats locked 24/7 to the grow ,,is ther any light in that room when the door is shut and locked, and its light off in the tent??
HTH
Gonna do some switching of fans and tighten up the ducting ASAPThe GrowBright 6" Inline Fan uses 110 watts and pushes 424 cfm of air, flange size 6".
Got duct tape and 15 feet of Velcro, Gonna cover up everything!
Spoke with HGTSUPPLy and ordered Gonna do some switching of fans and tighten up the ducting ASAP
Again, thanks brother