[Prince Buster]

Like me, you want to vaporize for health, but do not want to spend $200-600 on a Volcano, Valloon, or the valve kit etc.?

Well step right up because Prince Buster can give you the exact same sweet flavorful bag of medicine for under a hundred bucks!

Vriptech and MANY others recommend a heat gun with a ceramic heating element patented by Steinel. This is the most important component of your vaporizing, and key to keeping your lungs healthy. If you shop around you can find a no-name Steinel core gun for as little as $50, but once you badge the gun with Sears or Makita, the price goes up to $75-100.

I chose the Makita special ordered at Home DePOT. It was 75 bucks.

I had an old Reducer from an Ace Hardware Heat Gun(non-ceramic core)that fit the nozzle great.

[notpot]

is that all? i was hoping for more explanation?

[Prince Buster]

To make the hole in the test tube I just sanded it down until I had a 8mm hole.

Fill the tube with the required dosage.

Insert tube into PVC valve.

Set Makita dial to 1.9-2.0 and make sure valve is open.

Bag-o-meds

The Bags are good gor 5-6 big inhalations. The herb can be vaporized TWICE. Shake the tube a bit and fill up again!

After 10 or so bags there is a NICE collection of honey oil and trichomes at the venturi area and screen. I turn the Makita up to 4 to vaporize this pure medicine and boy is it potent!

[Prince Buster]

1.Makita HG1100 Heat Gun
Special Order @ Home DePOT for 71.99+tax
2. GLASS Test Tube 3/4in x 6in(20mmx150mm) $.99
3. 1/2in(10mm) O-Ring $ .20
3. Reynolds Oven Bags $1.50
5. 1/2 in PVC Valve (Part #EBV-0500-S / UPC# 1165114511) $3.99
6. Rubber band

I was going to do a how to, but really everyone..THIS IS SO EASY!

Here is a step by step:
BUILD
1)Sand test tube hole, wash clean
2)Stretch O-Ring around test tube
3)Place Stainless steel screen at bottom of tube, covering hole
4)Adjust PVC Valve and O-Ring mating
5)Use rubber band securing the Oven bag to PVC valve

USE
1)Have a place to set the Heat Gun down before medicating(like on a tile, because it's HOT!)
2)Insert tube filled with .3-.5G ground herb into PVC valve
3)Let heat gun run for 5 sec, then place nozzle into tube
4)Bag fills in approx. 40 seconds(Makita HG1100 set on low, TEMP @ 1.9-2.0 which is about 380 degrees)
5)Close valve

Medicate!

[notpot]

very nice!
thanks for the tip

[Prince Buster]

As for the PVC valve and health-

Because of the length of the glass test tube, the PVC valve component on this vaporizer design simply does not get hot or even warm. The glass gets a bit warm, but not hot at all. There is a subtle venturi effect from the heat gun reducer and the shape of the bottom of the test tube. Everything flows and works great with this system, and if you build it, you will not be broke or dissappointed!

[Babbabud]

nice thread ... very good idea and much more reasonably priced.

thanks alot

[Prince Buster]

I am also impressed with the ease of use and quality of the vapor with my DIY design. Generally the concept follows the Mystifier Vapor Tool(https://www.mystifier.com) but I (K)ept (I)t (S)imple after looking at the picture on the page and coming to the conclusion that what I saw looked like a Mad Scientist Lab. The Volcano is an amazing piece, it is just SO expensive for most people(even $420 at a med club is high!) The VRip Valloon is finally available, but again expensive, and is made mostly of glass.

I have experience medicating with both the Volcano, Valloon, and Vrip SVT bowl, Vapor Bros..all of them except the Vapir line(Which personally I think needs some R&D to make it better)

I have smoked herb to medicate every way possible, and am now a vapor-convert. Bubblehash and Honey Oil seem to vape better at higher temps with the K.I.S.S. so I turn the Makita dial up to 3.5-4 and get a sweet, heavy duty THC hit (It is best to sit down while inhaling as the rush is very potent and washes over ones body from brain to toes, relieving ailments along the way...Mmmmm)

If you build the K.I.S.S. Vaporizer, build a few at a time, and give them to your friends, patients, curious Bluntheads, and the people still trying to make these soldering iron/copper fitting/plastic tubing CANCER MACHINES. Have you read the back of your soldering iron/gun element lately, folks?
MOST Cheap soldering Iron elements are made with an ASBESTOS heating element!!! 30Watt Dollar Store and Radio Shack soldering irons clearly state that the iron is built with an ELEMENT that causes cancer and this is not a warning to just to aviod breathing in lead solder smoke while soldering! Go ahead and take one apart, you will see an ASBESTOS "sheet" rolled up in the metal tube. Oh yeah.. those Metal Ions clinging to your lungs can't be too healthy either.

PLEASE STOP MAKING SOLDERING IRON VAPORIZERS FOR YOUR HEALTH!

These Oven Bags(Turkey Size) are found for $1.50 for 2!

[HIGHRIDER]

Man this is a very informed thread i will try this before i buy a expensive. Do you think this could be converted to a bong or nice pipe? Just wondering,good lookin on the vap man can't wait to try it. Stay up HIGHRIDER

[zeppelindood]

very cool of you to share with us prince ~ rock it....