Stealth cab closetmaid 2 door - Page 3 - Micro Grows - International Cannagraphic Magazine Forums

jonhova · 01-17-2018, 04:32 AM

jonhova · 01-17-2018, 04:36 AM

Caulked the edges. Used trash bags; cardboard and gorilla tape to fix thr middle. The spot at the top middle is vety hard to light proof with the magnets in the way.

My fan was at the post office today. I didnt notice until it was closed sigh. Lighting and ventilation tomorrow.

jonhova · 01-18-2018, 04:37 AM

I have a question for you guys.

Can you recommend a clean way to wire cleat based sockets together without any exposed wire? Something with connectors if possible.

jonhova · 01-19-2018, 06:03 PM

I looked at target, 2 walmarts, officedepot, 2 cvs, and home depot for the traditional pencil holder carbon scrubber!

Fuck that! The larger oencil holder is not available anymore at officedepot/officemax near me. Most storesare 10 miles away that carry it and its over priced with shipping to my home.

Its a good thing i like digging old posts on icmag cuz i found a better solition that looks fucking slick as shit.

Check this out from dtokers thread.

Hobby crochet plastic and hot glue is gonna get this bitch done with some pantyhose, cd holder, and weather stripping.

jonhova · 01-20-2018, 06:48 PM

Glue gun and 6 sticks of glue
M2 x crotchet knitting mesh
Duct tape
Carbon
Stockings
White frabic polyfil stuff

Pretty much cooied dtokers design except made it longer. I bought fine particle carbon which worked its way through the mesh. This necessitated a layer on thd inner side of the larger mesh the polyfil white fabric to keep clthe carbon from going on thr outside of thr carbon filter. Attached it to a tupper ware w duct tale aftet sealing the carbon in with a fat weather stripping piece.

This will sit carbon facing up on the tupper ware on the top of the cab. Ill drill out a 2 1/2” hole with a hole saw and mount the fan.

jonhova · 01-20-2018, 07:39 PM

The new noctua NF-A6x25 FLX arrived. This is my main out take fan super quiet!

Coolermaster will be on the top blowing on the toos of the plants or on the leds.

repuk · 01-20-2018, 08:53 PM

Hi!

This is the explanation pic regarding how to apply panda film or mylar:

does it display fine? In this case (two doors) the sequence will be

left door - left wall - bottom - right wall - right door.

Weather striping on both doors, so that center (where both meet) is lightproof. I stapled everything just like you.

jonhova · 01-20-2018, 09:00 PM

I’ll take a pic of my current cab with a light on inside to show you my minor light leaks . I pretty much have it sealed except the top where the the cabinets meet at the magnets.

Athos · 01-20-2018, 10:41 PM

Quote:

Originally Posted by jonhova

The new noctua NF-A6x25 FLX arrived. This is my main out take fan super quiet!

So how do you like the fan, have you tried it yet? silent enough?

jonhova · 01-21-2018, 02:00 AM

This carbon filter will be covered eventually by some kind of inconspicuous box or enclosure.

The fan is quiet as shit Athos. Thank you for your recommendation.

I can feel air passing through the filter gently.

The light leaks are pissing me off. Bike inner tube seems to work the best of anything I've tried. Ill get a big strip of that staple it to the top wood panel and be done with it.

01-17-2018, 04:32 AM	#21
jonhova Member Join Date: Nov 2016 Posts: 303	Light proof middle and caulking
	Quote

01-17-2018, 04:36 AM	#22
jonhova Member Join Date: Nov 2016 Posts: 303	Part 2 Caulked the edges. Used trash bags; cardboard and gorilla tape to fix thr middle. The spot at the top middle is vety hard to light proof with the magnets in the way. My fan was at the post office today. I didnt notice until it was closed sigh. Lighting and ventilation tomorrow.
	Quote

01-19-2018, 06:03 PM	#24
jonhova Member Join Date: Nov 2016 Posts: 303	Thank you dtoker I looked at target, 2 walmarts, officedepot, 2 cvs, and home depot for the traditional pencil holder carbon scrubber! Fuck that! The larger oencil holder is not available anymore at officedepot/officemax near me. Most storesare 10 miles away that carry it and its over priced with shipping to my home. Its a good thing i like digging old posts on icmag cuz i found a better solition that looks fucking slick as shit. Check this out from dtokers thread. Hobby crochet plastic and hot glue is gonna get this bitch done with some pantyhose, cd holder, and weather stripping.
	Quote

01-20-2018, 06:48 PM	#25
jonhova Member Join Date: Nov 2016 Posts: 303	Carbon filter Glue gun and 6 sticks of glue M2 x crotchet knitting mesh Duct tape Carbon Stockings White frabic polyfil stuff Pretty much cooied dtokers design except made it longer. I bought fine particle carbon which worked its way through the mesh. This necessitated a layer on thd inner side of the larger mesh the polyfil white fabric to keep clthe carbon from going on thr outside of thr carbon filter. Attached it to a tupper ware w duct tale aftet sealing the carbon in with a fat weather stripping piece. This will sit carbon facing up on the tupper ware on the top of the cab. Ill drill out a 2 1/2” hole with a hole saw and mount the fan.
	Quote 1 members found this post helpful.

01-20-2018, 07:39 PM	#26
jonhova Member Join Date: Nov 2016 Posts: 303	Fans wired up The new noctua NF-A6x25 FLX arrived. This is my main out take fan super quiet! Coolermaster will be on the top blowing on the toos of the plants or on the leds.
	Quote

01-18-2018, 04:37 AM	#23
jonhova Member Join Date: Nov 2016 Posts: 303	I have a question for you guys. Can you recommend a clean way to wire cleat based sockets together without any exposed wire? Something with connectors if possible.
	Quote

01-20-2018, 08:53 PM	#27
repuk Member Join Date: Oct 2008 Location: Southern Spain Posts: 638	Hi! This is the explanation pic regarding how to apply panda film or mylar: does it display fine? In this case (two doors) the sequence will be left door - left wall - bottom - right wall - right door. Weather striping on both doors, so that center (where both meet) is lightproof. I stapled everything just like you. Attached Thumbnails __________________ Sativas are medicine for the mind. - ThaiBliss Tangwena's Malawi Cobbing Method Step by Step Diagram Repuk 3d take hybrid HML+HPS Stealth Garden Shed Repuk HMLED/Coco/BLumat stealth understairs micro grow Coco in an Ikea cab + thermo controlled CPU Fan
	Quote

01-20-2018, 09:00 PM	#28
jonhova Member Join Date: Nov 2016 Posts: 303	I’ll take a pic of my current cab with a light on inside to show you my minor light leaks . I pretty much have it sealed except the top where the the cabinets meet at the magnets.
	Quote

01-21-2018, 02:00 AM	#30
jonhova Member Join Date: Nov 2016 Posts: 303	Needs more bike inner tube light proofing This carbon filter will be covered eventually by some kind of inconspicuous box or enclosure. The fan is quiet as shit Athos. Thank you for your recommendation. I can feel air passing through the filter gently. The light leaks are pissing me off. Bike inner tube seems to work the best of anything I've tried. Ill get a big strip of that staple it to the top wood panel and be done with it.
	Quote