|
in:
|
|
| Forums > Talk About It! > Cannabis Concentrates > What ASMEstandard closed loop extractor parts should follow ? | ||
Post Reply  |
| What ASMEstandard closed loop extractor parts should follow ? | Thread Tools | Search this Thread |
09-02-2017, 11:38 AM
|
#1 |
|
Newbie
Join Date: Jun 2017
Posts: 20
 |
What ASMEstandard closed loop extractor parts should follow ?
I want to assemble a closed loop extractor from Glaciertank .
For the safety concerns , what ASME standard these parts follow ? And can I use quick tri-clamps ? |
|
|
|
09-02-2017, 05:55 PM
|
#2 | |
|
A Posse ad Esse. From Possibility to realization.
  
Join Date: Apr 2009
Location: River City, USA
Posts: 9,402
 |
Quote:
As LPG pressure piping, it must meet 350 psi, which the smaller sizes do, but the 6" does not with their 13MHP high pressure clamp. You will need to pick up a 6" SSH clamp at someone like LJ Star, which is rated over 400 psi.
__________________
An age is called Dark not because the light fails to shine, but because people refuse to see it. Believing is seeing and ignorance is bliss until it bites you in the ass! Fervor is the weapon of the impotent. The harder the sell, the poorer the product. Alas, my ignorance abounds; the more I've learned, the less I know that I know.......... Thou shalt seek and respect the opinions of operators, even unto the third helper, for theirs is a wisdom unknown to technicrats. Wise men learn more from fools, than fools from wise men. In my dotage I finally discovered that the secret to putting on pants both legs at a time is sitting down. |
|
|
|
|
|
09-04-2017, 04:00 PM
|
#3 |
|
Newbie
Join Date: Jun 2017
Posts: 20
|
Thank you GW .
And another thing is that I want to add sight glass on the extractor , but I read from your blog that there is a dangerous point to add sight glass between the dump valve and material tube . But from the article ,broken extractor image that I can see that the glass sight is not broken ? So does the sight glass is a factor that cause the explode ? And another question is that can i use a Long Tee | Tri Clamp to add the sight glass on extractor base so I can see the progress ? |
|
|
|
|
09-06-2017, 10:33 AM
|
#4 |
|
Newbie
Join Date: Jun 2017
Posts: 20
|
Any suggestions ?
|
|
|
|
|
09-06-2017, 12:31 PM
|
#5 | |
|
A Posse ad Esse. From Possibility to realization.
Join Date: Apr 2009
Location: River City, USA
Posts: 9,402
|
Quote:
A tubular sight glass is not suitable as a structural member taking periodic side loads. A stainless "tee" or cross with wafer type sight glasses, puts the glass under compression and will work.
__________________
An age is called Dark not because the light fails to shine, but because people refuse to see it. Believing is seeing and ignorance is bliss until it bites you in the ass! Fervor is the weapon of the impotent. The harder the sell, the poorer the product. Alas, my ignorance abounds; the more I've learned, the less I know that I know.......... Thou shalt seek and respect the opinions of operators, even unto the third helper, for theirs is a wisdom unknown to technicrats. Wise men learn more from fools, than fools from wise men. In my dotage I finally discovered that the secret to putting on pants both legs at a time is sitting down. |
|
|
|
1 members found this post helpful. |
| Post Reply |
«
Previous Thread
|
Next Thread
»
|
|
All times are GMT +2. The time now is 02:34 PM.
