Hey there Micro-growers, welcome to the Lodge! Pull up a chair and stay awhile. As they say, if the women don't find you handsome, they better find you handy.

I'd like to show you my little creation made with lot's of love and duct tape. My design is unique so if you've seen it before, that was probably me in another lifetime!

I'm not the first guy to make a growbox from stacked tubs. I've added enhancements to the basic design to have all features that the large cabinet growers are successfully implementing.

My growbox uses 6 x 42W CFL lights for 252W @ 100W/sqft. The growchamber and lightbox areas are separately ventilated similar to using a cooltube or vented hood. The lightchamber is cooled with a single computer fan. An activated carbon scrubber with a built in fan, removes air from the grow chamber to maintain total steath. I also manipulate the plant with screen of green, SCROG, to manage plant height and to maximize yield.

My growbox can be easily constructed using inexpensive household/hardware store items. Rubbermaids make really good growboxes. They can be easily cut with a utility knife and drilled and they are only worth $6 so if you make a mistake, get another one and start over. You can tuck it in a closet or down the basement. All the parts can be bought at Walmart or Home Depot. I also use fertilizers that can be bought at the grocery or hardware store too.

Grow Box Construction


Top Box

A 3 socket bathroom vanity fixuture is installed into the top box. To the right is a computer fan to exhaust the lights. Three exhaust holes and one intake are cut into the box. The intake for the lighting section is 5" x 5". It's very important to size the area of the intake to twice the exhaust to get maximum air flow from the fan.

I assembled all the parts then took everything apart before duct taping the emergency blanket to the inside of the box. Weather stripping is added to the edge of the box for a light seal and to keep the boxes from siding when stacked.

The inside can be painted as well. Use Krylon Fusion paint for plastic. Apply two coats of black paint first and then 2 coats of white. The tubs are a bit transparent and will glow if you only use white paint.

The acrylic light shield is laid on top of the lights and sealed with duct tape. Don't worry about the heat from the lights, CFL's don't run very hot.

Bottom Box

Two intakes are cut into the bottom box the same size as the dryer duct. The inside is lined with emergency blanket and weatherstripping is added to the edge.

Carbon Air Filter

My air filter uses two Sterilite containers. The small one must fit inside the large one.

The bottom is cut out of the small tub, I left a small rib in the center to support the screening.
Glue the window screen in place with the epoxy.

The lid of the large box is cut so that the small box with fit into it.

Intake holes are cut into the large box and the dryer adapters are fitted onto it. You can just duct tape it to the side if you don't have the adapters. This is probably the first time that duct tape is actually used for it's intended purpose. The flap is removed from the dryer adapter and I use a hack saw to trim off the pipe on one side.

A computer fan and a dryer hose adapter is fitted onto the lid of the small box.

When the filter is all assembled, I take silicone caulking and seal up crack where the small box goes into the large box lid.

My setup uses 1/2 lb of activated charcoal for a filter depth of 1" that I buy at the pet store. The 1" layer is good for the whole grow.

Assembled Growbox

Here is the growbox all put together.

I've used Kleenex boxes duct taped to the side of the growbox to act as light traps. The lighting heat is exhausted through dryer duct to the crack above the closet door.

Dryer duct is used to ventilate the box to the scrubber and then from the scrubber to above the closet door. The ducting is just duct taped to the side to the box. I leave a lot of slack in the dryer hose so I can take the top box off and set it aside.

This set up is very stealthy since the computer fans made virtually no noise and the fans are installed inside of the both the growbox and the filter. The ventilation works all on negative pressure, so all the smelly air is filtered.

Technical Details:

Anyone can stick some lights in a box but it's up to the ventilation system to make it work right. The basic rule for ventilation is that the intake area must be 2x the exhaust area otherwise the air flow will be restricted.

The lighting chamber is cooled by a computer fan pushing about 38 CFM. The exhaust air comes out at about 82-84F, but there is little heat transferred to the grow chamber. The lights run about 90F inside the lighting chamber.

The grow area of the box is ventilated by the scrubber with about 10-15 CFM. The air temperature exhausted is about 1-2 F above ambient. The air exchange rate is optimal to provide fresh air to the plants while not stressing the plants out by drying from too much air flow.

Drying Box

Here's my eazy to make drying box. I take a hanging file rack and tie some strings across for closelines and stick it in a rubbermaid tub with an intake hole cut in the bottom. I cut a hole in the lid and duct tape a Hamilton Beach Tru Air filter.

I also refill the filter cartridge with activated charcoal. Just cut a slit in the blue filter cloth, shake out the old stuff and fill 'er up again for pennies. Cover the slit with duct tape and you're in business.

[Maj.PotHead]

looks very clean and efficient

[JARofHERB]

HOLY SHIZAT.....
Woah man, nice rubbermaid grow box.. Such an innovative ventilation system..Fuc$ing cool man..Nice grow..

[supernerd]

Well show us what you're growing inside!

[bounty29]

That's an awesome design and grow, I love the ingenuity. How many cubic feet of air are in that box? I've got a 2'x2'x4' that I'm gonna be growing in, and I'm wondering if I could set up a carbon filter like that, I really like that design. You say yours works fine with a normal computer fan? I'd get a high power computer fan because of the increased space, I just didn't know if it'd be enough to pull through the carbon. I was thinking I could get an 84cfm fan for that, and then use another one for an aircooled hood for a 250w HPS. Interesting... I love how each time somebody posts their grow, it adds to and changes my design, I can't wait until everything is finally together!

[stonerpanda]

Kevvie from OG?? Glad to see you back, passing around that great design. I must have stared at those pictures for hours... the tissue-box light traps, the bathroom light fixture, rubbermaid carbon filter, this is a masterpiece of DIY. K+... er... i mean...