EmpireSeeds
Active member
Aero Cloner EZ-Cloner Materials:
1) 10-31+ Gallon Rubbermaid Bin
(Depending on Your Cloning Needs/ #'s)
(Some Tote's Leak Water-Luckily my 18 Gal. "RoughNeck" Doesn't
)
12.5 Gallon (50 Qt.)-10 Gallon Tote
This is a Nice 22 Gallon Tote w/Locking Handles (Handles are an Important Feature!!)
Personally, I Used the 18 Gallon 'ROUGHNECK'
It Nicely Fits x24 Un-Cramped 2" Insert/Sites with Space to Spare!!
-1 Spot (So x23 Spaces) For Pump Plug)
Having the Wire Passing Through Lid is a PAIN-IN-THE-ASS!! Everytime (4 Runs) I Lift The Lid (OFTEN, TRYING to Monitor the Water) The Wire Pulls The Pump Out of Place and Disturbs Everything, I Broke Several Stems Because of These!!
So, I Going to Re-Locate The Pump Wiring, Into the Bin Itself...
My Drill's Battery was Died...So It was Quicker (Than Charging Battery) to Do It By Hand...
Just a Quick Cardboard Stencil, Sharpie,
and Exacto Knife...
RESOLVED!!
I'm Back to a x24 Cloning Unit!!
2) Pump (300- 633+ Gph)
More Pressure (Gph) Better Atomization (Atomization = CLONES!!) (Cons: Bigger Producers More Heat)
3) Neoprene Inserts (1-3")
They Can br Easy Found on Ebay...
The EZ Clone Inserts are Thicker, However, They are a Smaller Diameter...
(I.E. 2" Ez Clone Inserts are 1 7/8")
These Yellow Pucks I Picked This Time, Are Thinner & Thicker Diameter (2" OD- Very Nice and Fit Snugly in 1 3/4" Cut Outs'
They Come in ALL KINDS OF COLORS!!
(Its Not My Ebay Auction, But Heres It Is
(He Sent me 64 Total Inserts) And You Can Pick Your Colors /or Even Miss-Match Them
They're the Best and Cheapest (Price Wise) on Ebay!!
1) 10-31+ Gallon Rubbermaid Bin
(Depending on Your Cloning Needs/ #'s)
(Some Tote's Leak Water-Luckily my 18 Gal. "RoughNeck" Doesn't
12.5 Gallon (50 Qt.)-10 Gallon Tote
This is a Nice 22 Gallon Tote w/Locking Handles (Handles are an Important Feature!!)
Personally, I Used the 18 Gallon 'ROUGHNECK'
It Nicely Fits x24 Un-Cramped 2" Insert/Sites with Space to Spare!!
-1 Spot (So x23 Spaces) For Pump Plug)
Having the Wire Passing Through Lid is a PAIN-IN-THE-ASS!! Everytime (4 Runs) I Lift The Lid (OFTEN, TRYING to Monitor the Water) The Wire Pulls The Pump Out of Place and Disturbs Everything, I Broke Several Stems Because of These!!
So, I Going to Re-Locate The Pump Wiring, Into the Bin Itself...
My Drill's Battery was Died...So It was Quicker (Than Charging Battery) to Do It By Hand...
Just a Quick Cardboard Stencil, Sharpie,
and Exacto Knife...
RESOLVED!!
I'm Back to a x24 Cloning Unit!!
2) Pump (300- 633+ Gph)
More Pressure (Gph) Better Atomization (Atomization = CLONES!!) (Cons: Bigger Producers More Heat)
3) Neoprene Inserts (1-3")
They Can br Easy Found on Ebay...
The EZ Clone Inserts are Thicker, However, They are a Smaller Diameter...
(I.E. 2" Ez Clone Inserts are 1 7/8")
These Yellow Pucks I Picked This Time, Are Thinner & Thicker Diameter (2" OD- Very Nice and Fit Snugly in 1 3/4" Cut Outs'
They Come in ALL KINDS OF COLORS!!
(Its Not My Ebay Auction, But Heres It Is
(He Sent me 64 Total Inserts) And You Can Pick Your Colors /or Even Miss-Match Them
They're the Best and Cheapest (Price Wise) on Ebay!!