Register ICMag Forum Menu Features Search Today's Posts Mark Forums Read
You are viewing our:
Forums > Marijuana Growing > Cannabis Growing Questions > Krypto's Ultimate Controler

Thread Title Search
Post Reply
Krypto's Ultimate Controler Thread Tools Search this Thread
Old 10-21-2004, 05:44 AM #11

Posts: n/a
We need to start drilling some holes.
I am going to use a 5 gallon bucket for the controler and a 3.5 gallon for the pots. Ideally your controler should be taller than your pots.
I am having a hard time finding black buckets and have found a supplier, but can't tell if what they carry is what we need by the pics in their catalog. I need those buckets, but will continue with what is readily available.
Notice the difference between the support at the top of each bucket?
The white Bucket is what I need because two of them fit into each other leaving a smaller amount of space between the two. This is necessary because you want your water/nutes to fill the medium bucket without Overfilling the flood bucket. You could just not fill your medium bucket completely, but that is not the ideal situation.
The White bucket is known as a Full Beam.

Lowes used to carry all black buckets but they've since changed to white. It may have something to do with Black not being Food Grade but It's a conspiracy against Marijuana Growers I tell yah .

You can use ANY type of bucket round, square or whatever, this is just what I have on hand .

Tomorrow we'll drill holes, set the float switches and whatever else we can get at . You will need a 13/16th inch spade bit .

Last edited by Kryptonite; 10-29-2004 at 05:48 PM..

Old 10-21-2004, 08:37 AM #12

Hooked-On-Grown's Avatar

Join Date: Mar 2004
Location: I'm in here.....somewhere...
Posts: 2,158
Hooked-On-Grown is on a distinguished road
I use 5 gal buckets with a tall 5 gal bucket for the controller. I used to clean pools and remembered the chlorine tabs came in a tall 5 gal bucket. I am using 3.5 gal on the inside of a 5. Give s me more room for a larger root ball.

Just waiting for my parts to arrive!!
Hooked-On-Grown is offline Quote

Old 10-21-2004, 08:41 AM #13

Posts: n/a
Damn fine info Krypto

I damn near ordered my parts also

Great thread


Old 10-21-2004, 12:14 PM #14

Bonzo's Avatar

Join Date: Sep 2004
Location: not quite sure
Posts: 4,008
Bonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to allBonzo is a name known to all
Basco has 6 gallon buckets, as well as all other sizes, i just received thier catalogue today. 6 gallon looks good for the controller if using gallon 5 medium buckets, or , 5 gallon with 3.5 inserts. this is great info Krypto, cant wait to start building new room and bucket system to go with. With the combined efforts of you and HOG anyone will be able to build an awesome, customized bucket system for half the price of store bought, not to mention the satisfaction of having built it themselves, i love that part
Bonzo BoUnCeS back...


"When one objectively acknowledges, accepts, and embraces one's weaknesses; they in fact, no longer continue to be that."(PTD)

Last edited by Bonzo; 10-21-2004 at 12:33 PM..
Bonzo is offline Quote

Old 10-21-2004, 03:02 PM #15

Posts: n/a
I also have their catalog Bonzo.
It's not very descriptive.
I don't understand the need for the smaller bucket in a larger one? Using the full beam buckets there is @ a 1.5 to 2 gap between the two which is sufficient. If you used the most common bucket with the rim like the black one shown here as your medium and flood buckets, you would have @ a 4" gap between them.

But this is just a guidleine, people can experiment and build various ways to suit their needs.

Old 10-21-2004, 03:42 PM #16
resident slackass

mybeans420's Avatar

Join Date: Feb 2004
Location: somewhere that has a pool table
Posts: 1,053
mybeans420 has disabled reputation
i really like that diagram. i think i've finally decided now how i plan on going hydro organic.
i'll have to put this thread to good use
"POWER TO THE PEACEFUL" micheal franti



"The prestige of government has undoubtedly been lowered considerably by the prohibition law. For nothing is more destructive of respect for the government and the law of the land than passing laws which cannot be enforced. It is an open secret that the dangerous increase of crime in this country is closely connected with this."
Albert Einstein, "My First Impression of the U.S.A.", 1921

"Prohibition will work great injury to the cause of temperance. It is a species of intemperance within itself, for it goes beyond the bounds of reason in that it attempts to control a man's appetite by legislation, and makes a crime out of things that are not crimes. A Prohibition law strikes a blow at the very principles upon which our government was founded."
Abraham Lincoln, U.S. President. 18 Dec. 1840

PLEASE don't PM me for seeds or cuts,.. Thank you
mybeans420 is offline Quote

Old 10-22-2004, 04:06 AM #17

Posts: n/a
Now your gonna need whatever vessel your going to use as a Controler Bucket. I've changed my mind and only need 3 lines going out. You can add more if you wish. I believe the original comes with 5.

Begin by marking for your feed to bucket lines 1 inch from the bottom of your bucket and two inches apart from one another.
If using 5 or more fill lines you should space them 1.5 inches apart. Using a 13/16ths inch spade bit, place the point of the bit on the mark you made for each hole and drill slowly and evenly so you will get a nice cut. When your finished, if your hole is not that smooth you can clean it up with sandpaper, a file or a utility knife.
It should look like this:

Completely opposite the holes you just drilled, on the other side of the bucket, mark a single spot one inch from the bottom of the bucket and drill. This hole will be used to connect hose from your return pump to the reserviour.
Directly above that hole one inch from the top of the bucket, mark and drill another hole. This hole will be used to connect your fill pump, which is in the reserviour to the controler.

It should look like this:

Last edited by Kryptonite; 10-29-2004 at 05:51 PM..

Old 10-22-2004, 04:35 AM #18

Posts: n/a
Before drilling for the switches sit your bucket down and decide which side you want your timer mounted on. It's a nuisence to have the timer facing a wall, you want easy access to it even though once it is set you rarely touch the thing.

You need to connect these two parts and make them leak free.

I tapped one end of the 90, wrapped a little plumbers tape around the threads i put into the 90, threaded the wires through it and screwed the float switch right in.

You could also push it in and seal it with a little hot glue or silicon.

For reference, the distance from the tip of the float to the center of the 90 is 3 inches.

Last edited by Kryptonite; 10-22-2004 at 05:34 AM..

Old 10-22-2004, 05:00 AM #19

Posts: n/a
The c-clip at the end of the float is approximately 1/8th of an inch thick. The thickness of the bottom of the bucket is also approximately 1/8th of an ich thick and there is approximately and 8th of an inch ridge around the bottom of this "particular bucket". These measurements are for the buckets I am using only, and will entirely depend on the size controler you will be building.
So now we have approximatley 3 and 3/8ths inches slightly heavier when measured from the outside of the bucket.

On the Side of your bucket mark and drill two holes, one 3 and 1/2 inches from the bottom of your bucket and the other two inches to the side of the last one and 3 and 3/4 inches from the bottom of your bucket. These two holes will be used to hold your bottom two switches, "drain switches" in place.

Should look like this:

Last edited by Kryptonite; 10-22-2004 at 05:39 AM..

Old 10-22-2004, 05:24 AM #20

Posts: n/a
Before we drill our final holes in the controler, we need to take some measurements on the buckets we will be using as our vessels to be flooded.
The bucket I am using is 11 inches tall. I like to keep the water/nute level at least 1/2 of an inch from the top of the flood buckets. From the center of the 90 to the end of the switch is 3 inches so we want to drill our holes at least 3.5 inches from the top, or 7.5 inches from the bottom of our controler. We want our water to reach that mark but not go beyond it.
note: I am setting these on a very level surface, if the floor in your area is not very level you may want to correct that figure by a half of an inch, 4 from the top, 7 from the bottom. This will lower the level of the flood in your buckets. If you make a mistake here it can easily be corrected bye placing a spacer either under your buckets or your controler.

Last edited by Kryptonite; 10-22-2004 at 05:43 AM..

Post Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT +2. The time now is 10:20 AM.

This site is for educational and entertainment purposes only.
You must be of legal age to view ICmag and participate here.
All postings are the responsibility of their authors.
Powered by: vBulletin Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.