CovertCrops
Member
I really like that carpet of Mass. SS! Do you veg in that room or a seperate area?
New room let me know what you think
- Thread starter P.D.S
- Start date
ItsAllOver
Devil's Advocate
I really like the use of cooltubes instead of duct runs, lol
Avon Barksdale
Member
kick ass setup nice and clean
madpenguin
Member
Room looks nice. Keep it up. 
There is a problem with your panel if you don't mind me saying so. Just trying to keep you safe. Your going to get some serious inductive heating of your feeder conductors having them in separate conduits like that.... Conductors of the same circuit need to be ran in the same raceway/cable/trench. Each wire will generate a magnetic field and they actually cancel each other out when run together. Split them up and encase them in a ferrous material and that insulation is going to get wicked hot.
Also looks like you've terminated some neutrals to the frame of the panel instead of the isolated neutral buss. Can't say for sure whether those white conductors are grounded or grounding conductors. Looks like you have 2 whites going thru each set set-screw so I'll assume you just didn't color code properly. Make sure you stay safe!!!
There is a problem with your panel if you don't mind me saying so. Just trying to keep you safe. Your going to get some serious inductive heating of your feeder conductors having them in separate conduits like that.... Conductors of the same circuit need to be ran in the same raceway/cable/trench. Each wire will generate a magnetic field and they actually cancel each other out when run together. Split them up and encase them in a ferrous material and that insulation is going to get wicked hot.
Also looks like you've terminated some neutrals to the frame of the panel instead of the isolated neutral buss. Can't say for sure whether those white conductors are grounded or grounding conductors. Looks like you have 2 whites going thru each set set-screw so I'll assume you just didn't color code properly. Make sure you stay safe!!!
P.D.S
Member
you caught me your right about running in a single race way but its what i had on hand and im only pulling 60 amps per pole with 4 Awg wire, since you mention it now i got to change it, the wire is generating minimal heat as is so im also not concerned,yet. Im planning to change a few thing so that will be added to the list, thanks for the looking out
the neutral are all terminated in the proper busbar and the grounds are in the proper busbar, look at the green tags on the white wire at the busbar directly connected to the panel and you will understand that all i had on hand was white and black wire and i marked the grounds with green tape
again thanks
the neutral are all terminated in the proper busbar and the grounds are in the proper busbar, look at the green tags on the white wire at the busbar directly connected to the panel and you will understand that all i had on hand was white and black wire and i marked the grounds with green tape
again thanks
madpenguin
Member
Yea. That's what I figured with the grounding conductors. Just makin' sure.
Here is a neat FLIR image of a Federal Pacific Double Pole Breaker that has failed (surprise, surprise...). You can see the incoming L2 phase really heating up and the breaker is on the verge of melt down. Doesn't have anything to do with inductive heating but your incoming L1 and L2 conductors would look similar to this picture due to being ran in separate conduits....
If any of you have access to one of these imaging devices, you should go out in the dead of night and scope your house out. Some of you would probably be mortified that you can tell exactly where your grow is located and exactly where you are exhausting air....
Here is a neat FLIR image of a Federal Pacific Double Pole Breaker that has failed (surprise, surprise...). You can see the incoming L2 phase really heating up and the breaker is on the verge of melt down. Doesn't have anything to do with inductive heating but your incoming L1 and L2 conductors would look similar to this picture due to being ran in separate conduits....
If any of you have access to one of these imaging devices, you should go out in the dead of night and scope your house out. Some of you would probably be mortified that you can tell exactly where your grow is located and exactly where you are exhausting air....
SaltyBalls
Member
lol dont think this is your first time nice job
SaltyBalls
Member
nice update that going to be one hell of a pull 
P.D.S
Member
To tell you the truth i can't remember as iv'e been working day and night and this is my first run with the girl, I will say this though out of all the strains in the room it smells the least and the Mass. super skunk is one stinking fuckin plant, smells like greasy diesel funk, Love the smell but willies makes up for smell with beauty . she has intense resin production and i can tell she gonna produce for me, I have a mother and if everything comes out like i think it will she will be on one table and ill alternate between salmon creek,Mass super skunk,Warlock and Bogglegum on the other table
Q
Quality control
Hey man, the screens looking excellent.
You planning on doing all screens next run? seems to be waisted light on the ones you have without the screen, another weeks veg would be good on those ones.
were they put in later than the ones with the screen?
Killer set up man,
You planning on doing all screens next run? seems to be waisted light on the ones you have without the screen, another weeks veg would be good on those ones.
were they put in later than the ones with the screen?
Killer set up man,
