Announcement

Collapse
No announcement yet.

Repuk HML/Coco/Blumat understairs stealth micro grow

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Repuk HML/Coco/Blumat understairs stealth micro grow

    Hi!

    The chamber
    The "chamber" is an understairs space, measuring 60x70cm (23"x28") area, 1.20m (4') height. Surface is 0.43 sq meter or 4,7 sq feet and volume is 0,5 cubic meter, or 18,7 cubic feet.

    One of the problems you face when trying to prop everthing up in the chamber "ceiling" is the unsderstairs concrete is a real PITA to drill, so I simply glued timber pieces to it, then screw all the hooks I need easily to it by hand.

    I built a 3 piece timber "frame", then hung the "door" on the upper frame. The door is a wood sheet with the reflective covering stapled to it.

    I stapled the reflective covering to the walls, fixed an AC inline extractor (120CFM) to the back wall. It vents through a wall air conduit, and pulls air through a Mountain Air Carbon Scrubber rated for 150CFM.

    I built a dimmer to regulate its speed, not only for noise, but to dial humidity. It's always on.

    A couple PC fans circulate air, one below the screens, one above, that will eventually have a twin soon.

    The Home Made LED (HML)
    Last week the items for my Home Made LED unit arrived and I built it.

    The items:

    100x25cm Finned Heatsink I cut in two 50 cm long pieces.



    Drivers: 2 Mean Well LPC-60-1050 driving a string of 12 XP-G WW each, and one LPC-60-1750 driving a 10 XM-L string (5 XM-L in each heatsink).

    LEDs (Cree already in MCPCBs):
    24 Warm White XP-G (5W)
    6 Neutral White XM-L (10W)
    4 Cool White XM-L (10W)

    Artic alumina thermal epoxy to glue the LEDs MCPCBs to the heatsinks.

    This gives 220Watts raw, will be run @ ~150-160Watts.

    The plan:

    Each heatsink has 12 WW XP-Gs, 3 NW XM-L and 2 CW XM-L (black circle: NW, red circle WW, blue circle CW):



    I tested all the LEDs, tinned the MCPCBs, mark their placement on the heatsinks, placed them w/o gluing yet to check the MCPCB "orientation" to ease wiring, then glued them, finished the wiring, tested for shorts with a multimeter, checked visually three times that the wiring was right, then hooked each string to its driver and lit them.



    I put an inline fuse in the positive rail with each of the strings: 1,5A for the XP-G's and 3A for the XM-Ls.

    I checked AC amperage, 0.25A the LPC-60-1050 (AC voltage read 232V), or 58W. The LPC-60-1750 0.4A. That's 90Watts, had me puzzled as expected the 1750 to be much more efficient.



    Mad brightness, had to be careful not to ever look directly to the lit chips.

    The heatsinks get hot, but you can touch them and hold the finger there.

    I have put them 15" (40cm) above the canopy. Still in 18/6, I intend to flip to 12/12 by mid week, still have to repot one clone and prop its screen.



    I vegged 2 seedlings: Somango on 16th Sept and Amnesia Haze one week later with a two 55W PLL fixture I built myself. A mate gave me a couple Atomic Haze clones, which have been vegging for a week under that same PLL.

    Lots of changes at once, something not advisable as if anything goes wrong there will be lots of variables to check, but... had no other chance:

    Swapped the PLL for the HML
    Repotted all the plants, but one clone, as ran out of coco!
    Fitted the modular screens
    Put the Tropf Blumat cones and its tubing
    Set up the reservoir

    I repotted to 11L pots and fitted the modular screens.

    The somango had to be severely bent/supercropped to fit under the screen.

    I gave them a dose of rhizotonic + B52 (PH 5.7, EC 0.9), until all the pots were well wet, then put the blumats that had been sitting in a water jar for a couple days on saturday, then fitted the tubing and setup the reservoir on Sunday. I adjusted each blumat so that it dripped 1 drop per second, then closed a couple markings.

    The reservoir has an small aquarium pump inside, that fires 15 minutes on, 15 minutes off.

    I filled the reservoir with tap water (0.4EC), adding Canna's coco A+B solution for EC 1.8, PH'ed to 5,6 and added Drip clean.
    Sativas Are Medicine for the Mind - ThaiBliss ...and Your Soul - Repuk


    Guides: Tangwena's Malawi Cobbing Method Step by Step Diagram Picture Displays Sideways? |How To Post Pictures | Wiring with WAGO's | Undersink RO Res Auto Top | Assemble Your Own DIY RO System
    Current: Repuk Goes to the Jungle (2020) | ACE Indoor 100% Salts Coco DTW Grow
    Past: HPS vs SILs Stealth Garden Shed Grow |ACE Ethiopian, Lebanese and Honduras Outdoor Grow | HMLED/Coco/Blumat stealth understairs micro grow | Coco in an Ikea cab + thermo controlled CPU Fan

    #3
    Nice clean setup! Looking forward to seeing this run.

    Are the Somango and Amnesia Haze fem seeds? or did you sex them already?
    Off the shelf retail store screw-in LED and CFL bulb comparisons

    1 sqft CFL Cab & other CFL micro cabs

    Comment


      #4
      looking good.. will follow this thread.
      DIY FAN BOX (LOW NOISE/LOW BUDGET)
      https://www.icmag.com/ic/showthread....80#post5372180

      Comment


        #5
        Originally posted by blynx View Post
        Nice clean setup! Looking forward to seeing this run.
        thanks!! I've followed your threads learning micro scrogs! A pleasure having a micro scrog master here!

        Are the Somango and Amnesia Haze fem seeds? or did you sex them already?
        Yes, they are feminized. I may have vegged the somango too much, but in a previous grow back In 2009 in SOG they came out with rather weak stems and fluffy buds so I thought I'd better let her gain strength. She has a rather thick and strong main stem right now... Hope it doesn't stretch too much as I don't have too much clearance to the HML...

        Glad to see you here baino! Welcome
        Sativas Are Medicine for the Mind - ThaiBliss ...and Your Soul - Repuk


        Guides: Tangwena's Malawi Cobbing Method Step by Step Diagram Picture Displays Sideways? |How To Post Pictures | Wiring with WAGO's | Undersink RO Res Auto Top | Assemble Your Own DIY RO System
        Current: Repuk Goes to the Jungle (2020) | ACE Indoor 100% Salts Coco DTW Grow
        Past: HPS vs SILs Stealth Garden Shed Grow |ACE Ethiopian, Lebanese and Honduras Outdoor Grow | HMLED/Coco/Blumat stealth understairs micro grow | Coco in an Ikea cab + thermo controlled CPU Fan

        Comment


          #6
          ModSCREENS

          I want to share what I learnt from a newbie perspective, so will comment on the other two key aspects of this grow that are new to me growing wise.

          The modular screens: modSCROG

          Having a fixed screen is something I don't like, but the idea of modular ones changes the game. Two great threads to check (learnt a ton from them!) VerdantGreen's: VerdantGreen's Quarters - 187 watt LED - Organic Modular ScrOG a great place to get a grip on modSCROG! and Blynx thread for micro scrog with tons of "daylapse" like pics.

          First step: making my mind on the pot size. As VG once told me SCROG plants are big ones crammed/convoluted in a small space, i.e. big pots = big yields.

          I use 100% coco, two key points are: coco doesn't need big pots as it's an hydro medium where we feed the plants on each watering as it doesn't have any nutrients itself; the another one being coco shouldn't be let to get bone dry, it's best when humidity is kept high or salt buildup and some other less than optimal conditions take place.

          I finally chose 11L (2,4gal) square sturdy plastic pots, keeping an eye on its height. I could have gone further and use 5.5 gallon (25L) pots, but that would make controlling relative humidity a hard task, and RH is key while flowering in such a small space.

          11L is a decent size, and by using blumats, a constant, per-pot customized dampness and feed can be maintained ensuring the plants will never lack nutrients.

          I chose them square for easier modular screen fitting. I drilled an array of holes on all the pot walls for better coco aireation and air pruning the roots. (Coco promotes incredible root growth), and also drilled the pot upper lip to screw from the underside of the lip to the modular screens.

          Following are some pics, I just used the exact same system VerdantGreen uses in his latter modSCROGs to fit the modular screens to the pots.

          I built the screens with timber, then cut and stapled "rubber cord" pieces making the net. This hollow rubber cord is sold to tie plants/branches without damaging the stems.

          An important thing when calculating the size is to let some clearance, i.e. my horizontal grow area is 60 cm x 73 cm, and I want to fit 4 modular screens, exact math would dictate that each will measure 30cm x 36,5cm.

          DON'T. Leave some clearance (I made mine 28cm x 34cm):

          Even when the grow space is the inside of a cabinet, where tolerances are small (rather bigger on a brick and mortar space) you will have a much easier time if you can easily take them in and out having some clearance to wiggle them, specially when they are "populated" by a flowering plant.

          It will also ease air flow through all the chamber.



          As you can see here the screen will be fixed to the pot lip using two off-center pieces of timber (inside the frame, left and right). I offset their centers relative to the frame height to lessen the tendency to rotate being fixed by just two points.

          This should be done with the pot at hand to test, I would have put the fixing timber pieces underneatch the frame, but when mocking up the setup with the pot I saw that screwing them inside the frame they happened to fit nicely the pot lips width.





          Pot lip to screen frame height is 15cm (about 6 inches). It isn't much I know, but I'm constrained in height:

          Remember I'm constrained in height as my DIY luminaries have 10W LEDs in it, and from what I've read, it should be kept between 30-40cm (12-15") from the canopy. Frame height from the floor is 42cm (~16,5"), so being the grow space height 1,2m (4') and the maximum height the HML can be lifted 105cm, that minus canopy distance leaves about 33cm for over the screen growth for a 30cm LED-canopy distance.
          Last edited by repuk; 10-31-2012, 09:52. Reason: added photos
          Sativas Are Medicine for the Mind - ThaiBliss ...and Your Soul - Repuk


          Guides: Tangwena's Malawi Cobbing Method Step by Step Diagram Picture Displays Sideways? |How To Post Pictures | Wiring with WAGO's | Undersink RO Res Auto Top | Assemble Your Own DIY RO System
          Current: Repuk Goes to the Jungle (2020) | ACE Indoor 100% Salts Coco DTW Grow
          Past: HPS vs SILs Stealth Garden Shed Grow |ACE Ethiopian, Lebanese and Honduras Outdoor Grow | HMLED/Coco/Blumat stealth understairs micro grow | Coco in an Ikea cab + thermo controlled CPU Fan

          Comment


            #7
            A little late , but I am 100% subbed !

            Out setups are quite similar, (I have a slightly large surface but lower height) and will be fun to compare this grow in the following weeks, even so you have a short advantage ( I germinated the seeds on October 15th) which I hope I will overcome (by using DWC) .
            sigpic
            "WARNING: Although using marijuana may not be addictive, growing it is."

            "The obscenity of hunting down low-level cannabis users to protect them is beyond absurd" - David Nutt

            Comment


              #8
              The blumats

              In my previous grows I used coco, and was impressed by the speedy and healthy growth it promotes, with the added benefit that being an hydro medium you know exactly what the plants are eating.

              I hand watered them, and that end up being a royal PITA, not being able to be away from home for several days, taking substantial time that I didn't have, and impacting plants development if a day in need of watering I wasn't able to do so.

              Right now I need blumats not for comfort but because due to the "environment" a week could pass before I could tender the girls.

              Blumats are porous clay cones resembling a carrot that act as "live sensors" of substrate humidity, opening the dripper when it falls below your set level.

              They don't need pumps, nor electricity.

              I'll try to write down a Quick Howto, summarizing what I found most important for me, but if you want to really learn about them, go to the original blumat thread, is a couple hundred pages long, but you have a direct link to post collection at the first post, then to DesertHydro's Blumat auto watering FTW! to get a hold of its use with coco.

              The Reservoir

              Blumats aren't intended for hydro but for soil, but can be used for coco with a nute solution as long as gumpy nutes, organic nutes or anything susceptible to clog the lines isn't added to the reservoir feeding solution.

              That doesn't mean you cannot feed whatever you want, by simply hand watering those nutes; the blumat will sense that and stop dripping... best of both worlds!

              Is it advisable to use an salt preventing additive to the nute reservoir, like Drip Clean, that will both prevent salts clogging the lines, and salt buildup in the pot's coco.

              Also note that you shouldn't use air pumps/stones inside the reservoir, as it will promote flocculation that will end up clogging the lines, or equally bad: air bubbles that end up clogging the lines. By continuous dripping and the nature of coco itself provides more than enough medium oxygenation.

              I used a jerrycan style plastic container I got for free at a car wash, washed and rinsed it thoroughly to get rid of any soap residue, filled it with tap water and left it a couple weeks emptying / filling it twice: a 26L (5,7gal) free reservoir.

              Mine is translucent, that should pose a problem with algae, but I keep it in a place that is always dark, so no problem. If you will let yours in a place which is usually lit, you should better get one non translucent, or simply cover it with a thick black trash can bag.

              Blumat installation: what will you need (pics follow)

              * Tropf Blumats (not juniors, nor maxies as long as your pots are below 5gal) one per pot. They come with an incorporated T.

              * 8mm line: a black or white, hard plastic tubing which is a PITA to work with.

              * 3mm line: a soft rubber, brown one, which is much more manageable. It usually sells in 5meter rolls.

              * 8mm T connector (to build a vent line)

              * Reservoir Thru-Hull connector: You must drill your reservoir and fit this, the rubber gasket goes inside, with the water.

              * Blumat valve: 2 of these Will make your life easier, put one at the reservoir "output", and another at the end of the line to ease air/bubble purging (more on this later)

              * Quick disconnect fitting, if you want to be able to "disconnect" the reservoir from the line installation for refilling, rinsing, etc. I used a 8mm quick disconnect intended for industrial pneumatic air installations. With this and the valve you'll be able to do so. See this post from BorkBorkBork I used the same but in 8mm, so no need for the clear tubing to adapt it.

              * Optional (if you don't use valves) Blumat End Piece, AND 3mm cap.

              Tropf Blumat:


              8mm T connector:


              Reservoir connector:


              Valve:


              End Piece:
              Last edited by repuk; 12-16-2017, 11:22.
              Sativas Are Medicine for the Mind - ThaiBliss ...and Your Soul - Repuk


              Guides: Tangwena's Malawi Cobbing Method Step by Step Diagram Picture Displays Sideways? |How To Post Pictures | Wiring with WAGO's | Undersink RO Res Auto Top | Assemble Your Own DIY RO System
              Current: Repuk Goes to the Jungle (2020) | ACE Indoor 100% Salts Coco DTW Grow
              Past: HPS vs SILs Stealth Garden Shed Grow |ACE Ethiopian, Lebanese and Honduras Outdoor Grow | HMLED/Coco/Blumat stealth understairs micro grow | Coco in an Ikea cab + thermo controlled CPU Fan

              Comment


                #9
                Blumats

                blumat installation: Howto

                The most common option is to run a single line of 8mm tubing that goes from the reservoir to the T connector of the first blumat, then to the second, the third... etc, until the last one, where you add a piece of extra line, then you can put an end piece with a 3mm cap shutting off the 3mm connector, or much better, ditch the end piece and put a blumat valve at the end of the 8mm tubing.

                Why? because once you get it installed, fill our res, etc, you'll need to open that valve (or remove the 3mm cap on the end piece) for air to escape letting water to go inside the lines. Not only at the first time, but in fact you should "purge" once a week, as air bubbles are blumats number one enemy.

                A more elaborated install, which I used, uses additionaly a "vent" to ease air bubbles venting, right after the hull reservoir connector, goes a T with one 8mm tubing that should be at least as high as the highest water level your reservoir will have.

                HeadyBlunts posted a very nice drawing that speaks for itself:



                The vent will provide a low resistance path for air to escape through it, rather than get trapped into the line or thru-hull connector.



                Here you can see closer the thru-hull, connector, the T with the vent, and the "quick release" connector: the grey thing on the right:



                It's better to install the T for the vent with the same orientation HeadyBlunts depicted, but I had to fit it this way due to space constraints.

                The blue thing is a plastic disc to aid in releasing the "quick release" pneumatic connector, which requires a fair amount of prying force in order for the tubing to be released. I didn't have the valves at hand so to release the tubing the reservoir must be emptied first... a no-no... get the valves!

                You may ask: Why the extra 3mm tubing? because although the blumats come with a T, and 3mm tubing that goes from the T through the blumat, is it much easier to route/work with the 3mm tubing than the 8mm hard tubing from the main line.

                You can replace the short (~5") 3mm tubing that each blumat brings stock and replace it at a lentgh that eases moving the pots, etc, leaving 8cm protuding from the blumat is enough.

                There's also the option to run a "closed loop" 8mm line, go to the HeadyBlunts posted for a detailed drawing.
                Last edited by repuk; 10-31-2012, 09:49. Reason: Added photos
                Sativas Are Medicine for the Mind - ThaiBliss ...and Your Soul - Repuk


                Guides: Tangwena's Malawi Cobbing Method Step by Step Diagram Picture Displays Sideways? |How To Post Pictures | Wiring with WAGO's | Undersink RO Res Auto Top | Assemble Your Own DIY RO System
                Current: Repuk Goes to the Jungle (2020) | ACE Indoor 100% Salts Coco DTW Grow
                Past: HPS vs SILs Stealth Garden Shed Grow |ACE Ethiopian, Lebanese and Honduras Outdoor Grow | HMLED/Coco/Blumat stealth understairs micro grow | Coco in an Ikea cab + thermo controlled CPU Fan

                Comment


                  #10
                  Originally posted by hempfield View Post
                  A little late , but I am 100% subbed !
                  A pleasure to have you here hempfield!

                  Out setups are quite similar, (I have a slightly large surface but lower height) and will be fun to compare this grow in the following weeks, even so you have a short advantage ( I germinated the seeds on October 15th) which I hope I will overcome (by using DWC) .
                  Aaaah, competition!!! DWC vs Coco+Blumats!! great!! It surely will be fun to watch!
                  Sativas Are Medicine for the Mind - ThaiBliss ...and Your Soul - Repuk


                  Guides: Tangwena's Malawi Cobbing Method Step by Step Diagram Picture Displays Sideways? |How To Post Pictures | Wiring with WAGO's | Undersink RO Res Auto Top | Assemble Your Own DIY RO System
                  Current: Repuk Goes to the Jungle (2020) | ACE Indoor 100% Salts Coco DTW Grow
                  Past: HPS vs SILs Stealth Garden Shed Grow |ACE Ethiopian, Lebanese and Honduras Outdoor Grow | HMLED/Coco/Blumat stealth understairs micro grow | Coco in an Ikea cab + thermo controlled CPU Fan

                  Comment


                    #11
                    Very nice informative thread so far..should produce some lovely ladies! Good vibez
                    "We must become members of a new race, overcoming petty prejudice, owing our ultimate allegiance not to nations, but to our fellow men within the human community." ~Haile Selassie I~

                    sigpic

                    Comment


                      #12
                      Originally posted by Irie_Lion View Post
                      Very nice informative thread so far..should produce some lovely ladies! Good vibez
                      Hope so! thanks Irie_lion! yummmm... Jamaica!
                      Sativas Are Medicine for the Mind - ThaiBliss ...and Your Soul - Repuk


                      Guides: Tangwena's Malawi Cobbing Method Step by Step Diagram Picture Displays Sideways? |How To Post Pictures | Wiring with WAGO's | Undersink RO Res Auto Top | Assemble Your Own DIY RO System
                      Current: Repuk Goes to the Jungle (2020) | ACE Indoor 100% Salts Coco DTW Grow
                      Past: HPS vs SILs Stealth Garden Shed Grow |ACE Ethiopian, Lebanese and Honduras Outdoor Grow | HMLED/Coco/Blumat stealth understairs micro grow | Coco in an Ikea cab + thermo controlled CPU Fan

                      Comment


                        #13
                        Looking awesome, subbed!

                        Comment


                          #15
                          Originally posted by repuk View Post
                          A pleasure to have you here hempfield!



                          Aaaah, competition!!! DWC vs Coco+Blumats!! great!! It surely will be fun to watch!
                          Not competition my friend : we will be like to pregnant ladies walking on the park, talking about pregnancy, changing baby food recipes , complaining about the long expectation until due date and so on

                          But hopefully, no pregnancy will occur neither on your or my growspace ! (even so I intend to do some breeding experiments this winter, but in a separate place of course).
                          sigpic
                          "WARNING: Although using marijuana may not be addictive, growing it is."

                          "The obscenity of hunting down low-level cannabis users to protect them is beyond absurd" - David Nutt

                          Comment

                          Working...
                          X